Ford c1 axle code.

It is a banjo-style axle as is the 8-inch. It was in production on many Ford cars and trucks, first appearing in 1957 and finally replaced by the Salisbury-style 8.8-inch axle in 1986, saving about 50 pounds and boasting increased efficiency. Here is an example of a weld repair on a factory original housing. Axle code 86 in Ford Ranger refers to the specific rear axle ratio that the vehicle is equipped with. It plays a crucial role in determining the overall performance and capabilities of the truck. The axle code 86 indicates a 3.73 gear ratio. This ratio signifies that for every 3.73 rotations of the driveshaft, the rear axle will rotate once. While some parts carried over from 2010, most 2011-up 10-1/2" Ford rear axle parts are not interchangeable with 2010 and older axle. Ford 10.5" full-floating rear axles were the only available axle for 2000-2005 Excursions plus 1999-2016 Ford F-250 and Single Rear Wheel (SRW) F-350 trucks. That said, you'll want to get closest to the same net ratio with your new tire size/gear ratio as you currently have with your stock tire size and gear ratio. Otherwise, your speedometer and odometer will both be off going forward. Craig. 2019 Transit, 148" WB, Medium Roof, 3.7L, 3.73 gearing.

What is the Ford Axle Code C1? The Ford Axle Code C1 refers to a specific axle ratio configuration used in Ford vehicles. It is important for understanding the gear ratio and performance characteristics of the vehicle. The Ford Axle Code C1 is a crucial factor in determining the performance and towing capabilities of a Ford vehicle.What is the Ford Axle Code C1? The Ford Axle Code C1 refers to a specific axle ratio configuration used in Ford vehicles. It is important for understanding the gear ratio and performance characteristics of the vehicle. The Ford Axle Code C1 is a crucial …Overview. Dexter, a premier manufacturer and distributor of axles, suspension, brakes, doors, venting products, trailer parts and accessories, and towing components serving …

Ford Rear Axle Assembly Identification - Page 06: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WEM-A: Bronco '66-'71: 4.11: ... Ford Pass., Mercury '67-'69: 3.10: 8 1/2 in: NL-Non-Removable Carrier: WER-AA:

It's 19 not I9. 1983/86 Ford Rear Axle / 3.55-1 / Non Limited Slip / 3750 lb. Rear Axle Capacity. 1987/91 Ford Rear Axle 8.8 / 3.55-1 / Non Limited Slip / 3800 lb. Rear Axle Capacity. The decoder in the parts catalog doesn't say whether 1983/86 is a 8.8 or a 9 inch. The 8.8's have a removable inspection cover, the 9's do not.1999 to 2016 Super Duty - axle codes - Hi guys, I tried searching the forum first for any info that telles me the axle codes on the inside door sticker for 1999 + superduties (particularly with Diesel) ie. C1, etc...thanks for your help! -CharlieAxle ratio and other information and specs for the Mustang. All Access Membership. Models. ... 1968 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 0: 2.50 open differential: 1: 2.75 open differential: A:What "axle" code is on the sticker on the drivers side door pillar? Find the code on the sticker then read the list below to find the gear info. Rick...-----Axle Type 31 — 3.73 non-limited slip, F-250/Excursion C1 — 3.73 limited slip, F-250/Excursion 32 — 4.10 non-limited slip, F-250 C2 — 4.10 limited slip, F-250/Excursion

3L isn't on the list I have from a specs doc from Ford. Here is all the axle codes I found for '05. ... 4n, axle, c1, code, codes, d1, d2, duty, e3, ew, f250, f350 ...

1999 - 2003 7.3L Power Stroke Diesel - Axle code D1 on the door tag. - 02 350 crewcab srw, what can yo utell me about my rear, or front axle?

The SERPING1 gene provides instructions for making a protein called C1 inhibitor, which is a type of serine protease inhibitor (serpin). Learn about this gene and related health co...That said, you'll want to get closest to the same net ratio with your new tire size/gear ratio as you currently have with your stock tire size and gear ratio. Otherwise, your speedometer and odometer will both be off going forward. Craig. 2019 Transit, 148" WB, Medium Roof, 3.7L, 3.73 gearing.I can only find F1 listed in the manual: F1 — 3.73 limited slip, F-350 (dual rear wheels) My truck has an F2 code on the door...I was wondering about the gear ratio. I have a 2001 DWR. Reply Like. # 4. 12-28-2006, 08:25 PM. Olddog66. Senior User.4. Axle Code 27 – 3.31 Open Rear Axle. This code designates an open rear axle with a 3.31 axle ratio. It strikes a balance between fuel economy and performance, being commonly found on F150s equipped with smaller engines. 5. Axle Code K2 – 3.55 Electronic Locking Rear Axle w/ Torsen Differential.Mar 26, 2023 ... In this video we go over how use the rear locking differential on a Ford. We are, PA's #1 Ford Store, Twin Pine Ford.A: The Ford axle code 4N is designed to improve fuel efficiency by allowing the engine to operate at lower RPMs while maintaining appropriate torque output. Lower RPMs mean less fuel consumption, making it beneficial for those who prioritize fuel efficiency.

I have a question on a rear axle swap for my 2004 Ford Excursion Diesel, what is the difference in rear axles? Obviously there's a difference between limited slip and not, but what are the differences in the other codes? I have axle code: C1 — 3.73 limited slip, F-250/Excursion This car is for resale, so I do not care if it is limited slip or ...October 20, 2003. #1. Axle Code:41. What gear ratio is it? 92 XLT 4x4. Thanks! 1996 Chevrolet Impala SS - ATI Procharged 383 Stroker LT1..lots more..try to catch me! 1974 Chevrolet Impala - Viper Killa (not … To find the axle code: 1. View the Safety Compliance Certification Label on the driver's side, front or rear door panel. 2. Find the word "AXLE" under the bar code. 3. Find the two-digit code under "AXLE." Step 2 - Find the Axle Ratio. To locate the axle ratio after you have found the axle code: Visit the RV & Trailer Towing Guides page on the ... Decoding Ford rear axle codes can be a bit complex, but by following a step-by-step process, it becomes much easier. Each letter and number in the rear axle code has a specific meaning, allowing you to extract valuable information about your axle. For example, the first two letters of the code indicate the axle’s size and capacity, while the ...What does Axle Code "C1" mean? Save Share. Like. Sort by Oldest first ... Ford also said i didnt have to change any filters internal or external. Runs great now and ...The Sterling 10.5 axle is an automotive axle manufactured by Ford Motor Company at the Sterling Axle Plant in Sterling Heights, MI.It was first used in model year 1985 Ford trucks. The axle was developed to replace the Dana 60 and Dana 70.The Sterling 10.5 axle is currently only made as a full floating axle.. 10.5 Sterling axle in 2011 Super Duty (without …

I'm planning on changing out the front and rear differential fluid in my Ranger and I have kind of a noob question. My truck has axle code R7. I've read that the R7 is an 8.8" L/S 4.10 ratio axle. My owner's manual states to add 4 oz of friction modifier XL-3 to the rear diff. for Traction-Lok axles along with 80w-90 fluid.Motorcraft® Axle Lubricants – Quick Reference Lubricant Applications and Capacities Chart – cont’d. When filling a Limited Slip axle requiring Friction Modifier, always add Friction Modifier first, before filling with the lubricant. [1] Oil refill volume does not include friction modifier. Do not overfill above volumes shown (friction ...

C1 for example is a 3.73 with limited slip. C2 is 4.10 LS, C3 is 4.30 LS. 31, 32, and 33 are 3.73, 4.10 and 4.30 open diff. There's a tag on the right side of the diff cover that has that info as well. My tag for example reads: 3V 425F 3 L 73 10 5 3E06 The first line has the plant code and axle type and revision.With a rear axil code of 18 you should have a 3.08. Not great for towing, If you have a 2wd that give you a max trailer weight of 4700#, 4x4 4600#. If you have to tow abunch and a lot of hills. you shold look at a 3.55 or …I'm trying to decode an axle tag that is in very bad condition. WDM-C1 = Ford 9" Rear Axle / 3.70-1 / No Limited Slip / 3,300 lbs. Rear Axle Capacity. 5EB = Assembled the 2nd week (B) of May (E), 1965 (5). The other jazz is the assembly plant code (3 digits) and design change (4th digit). Thanks ND.Oct 9, 2007 · 1947 and Older Ford Trucks; Bronco. 2021+ Bronco; 2021+ Bronco Sport; 1978 - 1996 Big Bronco; 1966 - 1977 Early Broncos; Bronco II; Ford Vans and other vehicles. 2014+ Transit; Transit Connect; 1968-Present E-Series Van/Cutaway/Chassis; Ranchero & 1961 - 1967 Econoline; Nite, Nascar & Other Limited Edition Ford Trucks; Performance, Engines ... The owner?s wallet card contains the original security code for keyless entry. Owners can typically find this card in the glove compartment of a Ford vehicle upon purchasing it. Th...Here is a picture of my door tag. Came from factory with a 4.30 axle ratio. Thanks Strokin, that is exactly what I was looking for. It seems like they left the axle code blank on a lot of 2000 models, mine doesn't have an axle code, and my company truck is a 2000 model with no axle code. Does anyone have a link for a VIN decoder that will give ...The correct link to use is http://www.fordification.com.

Jul 10, 2008 ... You will want to check spacing between leaf spring perches between the axle shafts to be sure the new axle will fit up there. Then check from ...

Ford Rear Axle Assembly Identification - Page 03: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDD-B: Ford Pass., Mercury '65: 3.00: ... C1: Cougar '67-'68 Comet '65 SW Mustang '65-'69: 3.00: 8 in: L: 28-WDJ-D ...

Ford Truck Enthusiasts Forums. Older, Classic & Antique Trucks. 1987 - 1996 F150 & Larger F-Series Trucks. 1989 E350 axle code C2 = ??? Notices. 1987 - 1996 F150 & Larger F-Series Trucks 1987 - 1996 Ford F-150, F-250, F-350 and larger pickups - including the 1997 heavy-duty F250/F350+ trucks.But I have seen a few listed that fit an 8" ring gear. His axle code is H9 which I found is a 3.55 Limited slip rear end, but I can't find any information as to what size ring gear I may have. The numbers on the rear end tag don't match anything I have seen listed anywhere. Rear end tag...6869B R 3L55 88 7F12.Motorcraft® Axle Lubricants – Quick Reference Lubricant Applications and Capacities Chart – cont’d. When filling a Limited Slip axle requiring Friction Modifier, always add Friction Modifier first, before filling with the lubricant. [1] Oil refill volume does not include friction modifier. Do not overfill above volumes shown (friction ...That said, you'll want to get closest to the same net ratio with your new tire size/gear ratio as you currently have with your stock tire size and gear ratio. Otherwise, your speedometer and odometer will both be off going forward. Craig. 2019 Transit, 148" WB, Medium Roof, 3.7L, 3.73 gearing.Sep 4, 2019 ... Here's a simple way to check your abs or wheel speed sensors on your car or truck. I'll show you the complete diagnosis and repair so that ...The Ford Super Duty axle code C1 points to a Ford Limited Slip differential with a gear ratio of 3.73. The capacity iS8500 pounds, GVWR, and points to single rear …The Ford 4N Axle Code refers to a specific rear axle ratio configuration used in Ford vehicles. It determines the gear ratio between the drive shaft and the rear wheel axle, which affects the vehicle’s performance, towing capabilities, and fuel efficiency. The 4N Axle Code is typically found on the vehicle’s door jamb or in the owner’s ...Welcome from South Texas. Welcome to the site. New Member Introductions - 1997 f250 4x4 C5 axle code - I've owned nothing but ford trucks for the last 20+yrs. but none from the 90s until now. I just bought a 97 f250 4x4 with 460 5speed the axle code is C5. I've found on this site that means 4:10 gear and limited slip with ford being the maker.1999 to 2016 Super Duty - Did Ford change the axle codes? - I've been looking for an 04 or newer F350, single rear wheel, 2 wheel drive truck. I've found a few and when asking the axle code, the numbers I get don't jibe with the tech info post at the top of the forum. ... C1 — 3.73 limited slip, F-250/Excursion C2 — 4.10 limited slip, F-250 ...

Axle codes for Ford Explorer, Ranger and Bronco II. Axle identification Ford Explorer, Bronco II, Ranger.Ford Axle Code Chart. Code Ratio Capacity Maker Type Yr. 12 2.73 3800 FORD REG 1991. 17 3.25 3300 FORD REG 1971. 17 3.31 3800 FORD REG 1995. 18 3.08 3800 FORD REG 1991.1999 - 2003 7.3L Power Stroke Diesel - C1 axle - I am in the middle of changing oil in my rear differential. I just want to be positive my axle is limited slip. It is labeled as C1, but there is are no L in any of the descriptions.Instagram:https://instagram. caltrans i80 conditionskronika's amuletdale bronner sermons 2022jenni rivera autopsy photos I got this one for a great price! I have noticed 1 flaw to this truck though, it is a 1 wheel wonder. I will get stuck in my own driveway! I dont want to keep using 4 wheel drive (2 wheel in reality lol) to move in my yard or driveway. I am looking to swap out my axle code 37 (3.73 non limited slip) to the 3L (3.73 limited slip).To find the axle code: 1. View the Safety Compliance Certification Label on the driver's side, front or rear door panel. 2. Find the word "AXLE" under the bar code. 3. Find the two-digit code under "AXLE." Step 2 - Find the Axle Ratio. To locate the axle ratio after you have found the axle code: Visit the RV & Trailer Towing Guides page on the ... immediate care lortonhow to remove roller brush from shark vacuum I got this one for a great price! I have noticed 1 flaw to this truck though, it is a 1 wheel wonder. I will get stuck in my own driveway! I dont want to keep using 4 wheel drive (2 wheel in reality lol) to move in my yard or driveway. I am looking to swap out my axle code 37 (3.73 non limited slip) to the 3L (3.73 limited slip). department of motor vehicles killeen texas Ford Color Codes - C1 model/year code C1 Cross-Reference. found 4 paint color chips with a manufacturer of "Ford", make/model/year paint code of "C1" sorted&nbs...Ford Rear Axle Assembly Identification - Page 03: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDD-B: Ford Pass., Mercury '65: 3.00: ... C1: Cougar '67-'68 Comet '65 SW Mustang '65-'69: 3.00: 8 in: L: 28-WDJ-D ...Axle Type 31 — 3.73 non-limited slip, F-250/Excursion C1 — 3.73 limited slip, F-250/Excursion 32 — 4.10 non-limited slip, F-250 C2 — 4.10 limited slip, F …